JB

Even way back then I kept a notebook with all of my darkroom procedures laid out in a step-by-step fashion. This way I knew I would always do things exactly the same. I used the same graduates, arranged in the same order every time. Developing film is a one shot deal. Make a mistake and that is all she wrote. At this point in my progression with film and darkroom, I had become confident in my ability to develop film. The process had become the first step on the way to making prints.

My procedure for film was simple. I would line up my chemical containers in the correct order. Fill them with the proper liquids and adjust the temperature. Then I would head to my closet darkroom to load the film into the developing tank. I used a 16oz tank that held two reels and I usually did two rolls at a time. I loved the Rodinol because it came in a stock syrup and was mixed something like 1:200, if memory serves me correctly. I would measure the stock using two small syringes since it only took a few milliliters to make up the developer. I would lay the syringes, once loaded, next to the container marked developer which contained distilled water. I always have used presoak, so once the film was in the presoak, I would empty the syringes into the developer container and stir up the developer. Not much to it, simple and easy. Usually took me about forty five minutes from start to hanging up film to dry.

Now this one particular Saturday myself and a few friends went out and I shot two rolls of film that day. Later that evening we returned to my place for a few beers and by about 8:00 everyone headed home. I had this bright idea that if I processed the film from the day it would be dry and I could print it Sunday. Nothing to it, just get out the notebook, measure and slosh. . . processed film!

There was nothing very special about this film run, except the slight fog in my head from the beers and maybe a little to much sun. Everything went as usual. Once the film was washed I unrolled the first strip to find it completely clear end to end. The second roll was the same. What the @#$%^*? My first thought was the camera quit working. As I sat there perplexed I looked at my processing line and what do you think I saw? There next to the empty container for the developer lay my two syringes with the stock Rodinol still in them. I had failed to mix the developer. I learned right there that plain distilled water will not develop film. I also immediately enacted a strict rule in the darkroom; NEVER MIX RODINOL AND BEER!

JB

Those that dictate hard and fast, unwavering, rules for the creation of art usually are the vane, egotistical, self-centered types that are full of their own over-inflated view of their importance and try to tell you that cropping is an unforgivable sin.  I say. . . Not True!

No one has the authority, nor the right, to tell you what, nor how, to create your art.  Cropping is a personal decision, and can only be justified by you as an individual.  If cropping helps any particular photograph, then it is no sin to proceed to crop away.

Cropping is best done in the camera at the time you make the negative, but it is not always possible.   There will always be those instances that appropriate framing is just not possible in the field.  Never pass up an opportunity just because the perfect image does not exactly fit the film.  Keep cropping as an option.   Do not dismiss anything that will help.

During the printing process look carefully at your first work print and determine if the image is strong from corner to corner.   Use cropping L’s to mask questionable edges of the image and determine if lopping off some of the image will strengthen it.   If you are enlarging you can reset the easel and the print size.  If you are contact printing, a rotary trimmer is your best friend.   The choice is totally yours.  Do not be a slave to others opinions.  There are no rules.  The decision is so eloquently expressed by Bob Segar:  “What to leave in, what to leave out. . .”

If cropping does not improve the photograph, maybe it is a good idea to find another image that will be more expressive.   If you do hit a brick wall with a photograph, save your work and put it aside for later.  There are few negatives of questionable substance that are worth killing yourself in order to print.  You are usually better off to concentrate on those that are not a struggle to print.

It is easier on you and more productive, and less frustrating, to make negatives that are well seen and easy to print.  A mastery of craft will make everything work more smoothly, but never let anyone tell you that you should not, can not, crop your photograph.  Just don’t go there!  Cropping can be your best friend.

JB

Ever found that once you have your camera in just the right position that you can’t quite see the very top of the ground glass. It is important to get up there so you can see if your foreground is in focus. Never fails, you need just a little more to get a good view. Well, we found a neat accessory that just may save the day for you.

We discovered a nifty little folding step stool at Wal-Mart. We hauled a couple of these with us on our last trip and though I never used mine, Susan found it very helpful with several of her photographic efforts. It was especially useful for her and the pano format cameras she uses.  She made use of the step several times when she needed a little height working with difficult setups.

Here is more information from the Wal-Mart web site;

Keep everything within reach with the Mainstays 12″ Folding Step Stool. This skid-resistant step stool gives you an extra boost to reach high shelves or cabinets. It folds down to two inches thick for easy storage.

Mainstays 12″ Folding Step Stool:
Easy to carry
Skid-resistant top and feet
Stands 12″ high
Folds to 2″ thick
Weight capacity: 300 lbs
Folded Size: 13.5″ x 12.5″ x 2″
Weight: 2.5 lbs
Wal-Mart No.: 007126355

This 12″ step folds up and is easily tucked away till you need a little boost.  This is another accessory that is a life saver when you need it. We ended up purchasing several of these for use around the house also. You never know what you are going to find when you are out poking around in the stores.

JB

It is obvious that you need to keep your camera clean and it is imperative that you vacuum out all of your film bags and equipment cases. Dust gets everywhere, and it is good practice to vacuum everything before you go out to photograph. But, there is one area we have found to be extremely important for dust control, and that is keeping your film holders clean.

We have found that a thorough cleaning of every holder just prior to loading film keeps the dust problem to a minimum. If the inside of the holder is clean, then the outside is the only place where dust resides. Realize that the most critical time is before and during exposure. If a dust speck gets on your film after exposure, at least it is no longer a threat for making the dreaded pinhole which leads to the black spot on the print. After exposure, the worst a dust speck can do is possibly scratch the film during handling.

Everyone has their own methods for cleaning and loading film holders, and here are my main concerns and how we prepare our holders for loading. I will begin by saying that every holder is cleaned and inspected just prior to every loading session. Even on the road, we never load a holder with fresh film without cleaning. My biggest concern is dust inside the holder. I want the inside to be as clean, and dust free as possible. No matter how clean your film bags and cameras are, dust will always settle on the outside of the holders. If you thoroughly clean the inside of the holder, you will have a better chance of keeping the film dust free. I begin by cleaning the work surface with a damp towel and after dry I vacuum the area just to be sure. I always use the round brush on the end of the vacuum hose and before attaching I vacuum it well to make sure the bristles are free of dust.

I work each holder individually and begin by vacuuming the entire outer surface of the holder with the dark slide still in place. I pay particular attention to the entire area around the parameter of the holder where the slide meets the holder. I want the exterior of the holder as dust free as possible before I remove the slide.

One area that collects dust is the light trap area. Any dust on the dark slide will be wiped off by the felt in the trap. It is imperative that the dark slide be completely removed and the light trap vacuumed thoroughly. Also, while the dark slide is out of the holder, I vacuum the inside of the holder and the entire parameter, paying special attention to the film hold down and dark slide slots along the sides. I open the loading flap and vacuum under it also. The last thing I do before reinserting the dark slide is vacuum both sides of the slide and inspect it for dust or any possible damage. Each dark slide is removed, one-at-a-time, and always replaced in the same side of the holder. I never mix up slides, they always go back into the same holder and same side. . . always!

Once the holders are cleaned we immediately load them with fresh film and place them into their film bag. It is a good idea to vacuum the film bag before placing newly loaded film holders back inside. This is a good idea, especially if you have been in a particularly dusty area.

This is the ritual we go through every time we load film and we have little problems with dust on our film. Everyone has their own way of doing things and this is the procedure we use when loading film. There are a few things that we have found that greatly improve the odds of keeping your film clean. Remember, the vacuum is your best friend when it comes to dust. See my previous post titled “DUST. . . A Four Letter Word!” for more information.

JB

Click HERE to go to the sample album.

SAMPLE GALLERY

If you were ever curious as to how photographic film is manufactured, then I can highly recommend a great book on how Kodak makes film. “Making KODAK Film; The Illustrated Story of State-of-the-Art Photographic Film Manufacturing” by Robert L. Shanebrook, is a book I can suggest to answer the majority of your questions about  what goes into manufacturing film. I will quote from the author’s web site;

Information in the book

The book was compiled based on my personal experience plus the input from Kodak experts. Kodak provided access to Kodak Park and assigned experts to the project. Typically the experts explained the operation to me and then accompanied me as I photographed. After I retired I spent over forty days photographing in Kodak Park and many more days in discussion.

In addition, I was aided by input from 24 Kodak retirees. In most cases the retirees were the predecessors of the current Kodak experts that helped me. I also utilized the advice of ten experts from outside Kodak. To insure accuracy the manuscript was reviewed by many of the people that provided information used in the book.

I am grateful to over ninety people who helped me with the book.

Author

Bob Shanebrook graduated from Rochester Institute of Technology and worked at Eastman Kodak Company for 35 years before retiring in 2003. At Kodak he worked as a commercial photographer, researcher, product development engineer, film manufacturing manager, and for over twenty years was a Worldwide Product-Line Manager for Kodak Professional Films. He was involved in nearly all aspects of Kodak’s black-and-white and professional film business.

I highly recommend this book to anyone interested in learning about the art and craft of film manufacturing. For me this was a slow read since the book is mostly photographs. They say a picture is worth a thousand words, with some of these machines, it may be more like ten thousand.

Mr Shanebrook has self published this book and I can recommend it is a good one. . . two thumbs up from me. A great read if you are interested in just how complex the film in your camera is to produce. More information and how to order a copy from the author can be found HERE.

JB